Daikin U4 Error: What It Means, and a Real Oran Park Job

A Daikin ducted at an Oran Park rental showing U4. Here's what the code means, how we track it down, and what we found.

Daikin U4 Error: What It Means, and a Real Oran Park Job

What A Daikin U4 Error Means

U4 is a communication error. The indoor and outdoor units have stopped talking to each other, so the system shuts down to protect itself. You'll usually see the code flashing on the wall controller, and the system won't heat or cool.

It's one of the most common Daikin codes we get called out for. The cause can be as simple as a loose wire or as serious as a failed circuit board, and the only way to know is to test it properly. Swapping parts and hoping is how people end up paying for a board they didn't need.

How we diagnose a U4, step by step

  1. Read the error history on the controller. It tells us when the U4 started and what other codes came before it.
  2. Reset the power and confirm both the indoor and outdoor boards power up normally.
  3. Check the wiring terminals at both units, making sure they match and are done up tight.
  4. Walk the communication cable through the roof looking for rodent damage or crushed sections.
  5. Test the cable end to end, then confirm the two units are actually sending a signal to each other.
  6. Check every plug on the boards by hand, and test safety switches like the high pressure switch.
  7. Put gauges on to rule refrigerant in or out.
  8. Run the outdoor unit in test mode, and if needed on its own with the comms disconnected, to prove whether the board is at fault.

What not to do

  • Don't keep cycling the power over and over. One restart at the isolator, left off for five minutes, is fine. If U4 comes back, leave it off and book a tech.
  • Don't open up the outdoor unit yourself. There's mains voltage in there and capacitors that hold a charge after it's switched off.
  • Don't let anyone replace a board without testing the wiring first. A lot of U4s are wiring, not boards.

For the full list of codes, see our Daikin error codes guide.

The Job

  • Suburb: Oran Park
  • Job: Diagnostic, booked through the real estate
  • System: Daikin 12.5kW ducted
  • Price: $250+GST diagnostic fee

The tenants' ducted system wasn't heating or cooling properly. The real estate booked us in.

What We Found

The controller's error history showed a U4 communication fault, plus a U0 low-gas code from the year before.

Opening up the outdoor unit, we found the reversing valve plug disconnected, with a bent pin. The reversing valve switches the system between heating and cooling. A loose plug there can make a system behave like it's low on gas, which is very likely what happened last year. Someone had been in there before and missed it.

We also tested the comms cable end to end, and it was fine. The outdoor board itself was faulty.

The readings

  • Refrigerant pressure right for the temperature on the day
  • Comms cable tested end to end: good
Disconnected reversing valve plug with a bent pin on a Daikin outdoor circuit board
The reversing valve plug, off its pins.
Daikin controller screen showing U4 and U0 error history
The error history on the controller.
Daikin ducted outdoor unit opened up for diagnosis beside a fence
The outdoor unit, very close to the fence.

What We Did And Recommended

We straightened the pin and refitted the plug. The outdoor board needs replacing, and we recommended air deflectors as well, because the unit sits too close to the fence and recirculates its own air.

For landlords and property managers, a written report like this means you know exactly what was found and why, not just an invoice.

More on Daikin error codes, Daikin repairs, and air conditioning in Oran Park.

Jay's Air Conditioning white icon logo showing the flame and tick brand symbol on a light grey background

FAQ

Common Questions

FAQ

It’s a communication error between the indoor and outdoor units. They’ve stopped talking to each other, so the system shuts down. The cause can be wiring, a loose plug or a faulty circuit board.

You can try one reset: turn it off at the isolator, wait five minutes and turn it back on. If the U4 comes back, it needs a licensed tech to test the wiring and boards. Don’t open the outdoor unit yourself.

Our diagnostic is $250+GST. That covers the testing to find the cause. If parts are needed, like a board, we quote the repair once we know exactly what’s wrong.

Sometimes the fault isn’t where you’d look first. On this Oran Park job, a reversing valve plug was off its pins inside the outdoor unit. You only find that by checking every plug by hand, which is part of our process.

Get A Report Like This For Your System

Every Standard Service ($250+GST, $110+GST for each extra unit) comes with a written report like this one, with readings and photos, emailed to you the same day. Diagnostics are $250+GST and come with a written report too.

Give us a call on (02) 9820 4500 or book online. Our own crew, not subbies. NSW contractor licence 273312C, ARCtick AU13058. Servicing Sydney since 1991.

See all our service reports