
The customer said no issues. The readings picked up low superheat and a surging compressor.
What Superheat Tells Us: A Gregory Hills Early Warning
What Superheat Is, And Why It Matters
Superheat is how much the refrigerant has warmed up after it's fully turned to vapour, before it reaches the compressor. It tells a tech whether the gas is flowing through the coil the way it should.
Low superheat, close to zero, can mean some refrigerant is reaching the compressor before it's fully turned to vapour. Compressors are built to pump vapour, not liquid, so over time that can wear them. It's the kind of thing you only see with gauges on and the system running for a while.
What we test on a service, step by step
- Clean the return air filter.
- Run the system for about 30 minutes so the readings settle.
- Measure return and supply air temperatures to check heating or cooling performance.
- Check supply voltage across all phases, and compressor and fan current against their ratings.
- Test the fan capacitors against their rated value.
- Read the low and high side pressures, subcooling and superheat.
- Look for oil marks, which can point to a leak, and bubble test anything suspicious.
What not to do
- Don't ignore a new pulsing or surging sound from the compressor.
- Don't assume no complaints means no issues.
- Don't add gas to a system that already has plenty. It can make low superheat worse.
See air con making noise and Actron repairs.
The Job
- Suburb: Gregory Hills
- Job: General ducted service
- System: ActronAir 12.4kW ducted, Copeland scroll compressor, R410A
- Price: $250+GST
A general service. The customer had no complaints.
What We Found
We ran it in heating for about 30 minutes with the gauges on, at around 12 degrees outside. Superheat was close to zero, and after 28 minutes the compressor started a pulsing, surging sound.
There were oil marks on the suction valve. Oil marks can mean refrigerant escaping, so we bubble tested it, but no leak showed up on the day.
The readings
- Return air 21.6 degrees, supply 41.6 (a 20 degree rise in heating)
- Supply voltage 422 / 422 / 423V
- Compressor 5.60 / 5.59 / 5.26 amps, against 8.0A maximum
- Capacitors 3.90 and 4.08uF, indoor fan 1.3A
- Standing 1,138 kPa, low side 858, high side 3,341 kPa, subcooling about 15
What We Did And Recommended
The filter was chemically cleaned. The noise and the oil marks are written up in the report to recheck at the next service.
Nothing needed fixing on the day, but if this turns into a leak or a compressor problem, the customer has a dated record showing when it started.
More on air con making noise, Actron repairs, and air conditioning in Gregory Hills.
FAQ
Common Questions
It’s how much the refrigerant has warmed up after turning to vapour, before it reaches the compressor. It shows whether gas is flowing through the coil properly.
Close to zero can mean some refrigerant is reaching the compressor before it’s fully vapour. That isn’t good for the compressor long term, so it’s worth watching.
Sometimes. Refrigerant carries oil, so a leak can leave oil behind. On this job we bubble tested the area, found no leak, and noted it to recheck.
Because readings can pick up early warnings, like this one, while it’s still cheap to deal with. You also get a dated record if something fails later.
Get A Report Like This For Your System
Every Standard Service ($250+GST, $110+GST for each extra unit) comes with a written report like this one, with readings and photos, emailed to you the same day. Diagnostics are $250+GST and come with a written report too.
Give us a call on (02) 9820 4500 or book online. Our own crew, not subbies. NSW contractor licence 273312C, ARCtick AU13058. Servicing Sydney since 1991.
